View TFS167G_1324438.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

TFS167G.doc
version 2.2
14.11.2003
VI TELEFILTER
Measurement condition
Ambient temperature: 23 C Input power level: 0 dBm Terminating impedances at fc *: input: output:
Filter specification
TFS 167 G
1/5
325 325
// -8,0 pF // -8,0 pF
Characteristics
Remark:
Reference level for the relative attenuation arel of the TFS 167G is the maximum of the pass band attenuation amax. The maximum of the pass band attenuation amax is defined as the insertion loss ae. The centre frequency fc is the arithmetic mean value of the upper and lower frequencies at the 3dB filter attenuation level relative to the insertion loss ae. The nominal frequency fN is fixed at 167,0 MHz without tolerance. The given values for the relative attenuation a rel and for the group delay ripple have to be reached at the frequencies given below even if the centre frequency fc is shifted due to the temperature coefficient of frequency TCf in the operating temperature range and due to a production tolerance for the centre frequency fc.
Data
Insertion loss (Reference level) Nominal frequency Pass band Amplitude variation in PB Amplitude ripple in PB Relative attenuation fN 0,4 MHz ... fN 0,6 fN 0,6 MHz ... fN 20,0 fN - 20 MHz ... fN - 137 fN + 20 MHz ... fN + 103 fN +103 MHz ... fN + 105 fN +105 MHz ... fN + 833 Absolute group delay in PB Group delay ripple in PB Intermodulation ratio For two - 20dBm input signals @ fN + 0,800 MHz and fN + 1,600 @ fN - 0,800 MHz and fN - 1,600 Input Return loss Output Return loss Input power level Temperature coefficient of frequency Tc f Frequency inversion temperature Operating temperature range Storage temperature range p-p
arel
typ. Value
ae 1,4 dB
Tolerance/Limitation
max. 3,0 dB
fN PB
318 kHz fN max. max.
167,0 MHz 75 1 kHz dB
0,5 dB
MHz MHz MHz MHz MHz MHz
9,0 18,0 40 40 65 40 1,71 240 MHz MHz 18,0 20,0 40
dB dB dB dB dB dB s ns
min. min. min. min. min. min. max.
5 10 30 30 40 30
dB dB dB dB dB dB
2,0 s ns dB
max. 300 min. 100
dB dB
min. min. max.
15,0 dB 10,0 dB 22 dBm
C
2
-0,032 ppm/k -
- 5 C .. + - 40 C.. + 85 90 C C
*) The terminating impedances depend on parasitics and q-values of matching elements and the board used, and are to be understood as reference values only. Should there be additional questions do not hesitate to ask for an application note or contact our design team.
generated: checked / approved:
TELEFILTER GmbH Potsdamer Strae 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: tft@telefilter.com VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.
TFS167G.doc
version 2.2
14.11.2003
VI TELEFILTER
Filter specification
TFS 167 G
2/5
Construction and Pin Connection
(All dimensions in mm)
13,31 0,20
TFS 167G R29
date code
1 2 3 4 5 6 7 8 9 10
input ground ground ground output output ground ground ground ground year + week 2001 2002 2003
date code: N P R ...
1,00,2
1,910,2 7,620,2
50
matching circuit:
L2 1 5 LB-OUT 200Ohm : 200 Ohm Output C1 10
L1 Input
SAW
L3
6
2,3,4,7,8,9
TELEFILTER GmbH Potsdamer Strae 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: tft@telefilter.com VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.
TFS167G.doc
version 2.2
14.11.2003
VI TELEFILTER
Stability Characteristics
Filter specification
TFS 167 G
3/5
After the following tests the filter shall meet the whole specification: 1. Shock: 500g, 18 ms, half sine wave, 3 shocks each plane; DIN IEC 68 T2 - 27 10 Hz to 500 Hz, 0,35 mm or 5g respectively, 1 octave per min, 10 cycles per plan, 3 plans; DIN IEC 68 T2 - 6 -55 C to 125C / 30 min. each / 10 cycles DIN IEC 68 part 2 - 14 Test N
2. Vibration:
3. Change of temperature:
4. Resistance to solder heat (reflow):reflow possible: twice max.; for temperature conditions, please refer to the attached "Air reflow temperature conditions" on page 4;
Packing Tape & Reel: DIN IEC 286 - 3, with exception of value for N and minimum bending radius; tape type II, embossed carrier tape with top cover tape on the upper side; max. pieces of filters per reel: reel of empty components at start: reel of empty components at start including leader: trailer mm 1700 min 300 mm min 500 mm min 300
Tape (all dim ensio ns in mm ) W Po Do E 24 4 : 1,5 : 1,75 : : 0,3 0,1 + 0,1 0,1
Po
EMBO SSED CA RR IER TAP E
Do
P2
E Ao F W
F : G (min) : P2 : P1 : D1(min) : Ao : Bo Ct : :
11,5 0,1 0,60 2 0,1 12 0,1 1,5 7,1 0,2 13,9 21,5 0,2 0,1
D1 Ct Bo
G
P1
COVE R TAP E
W2
Reel (all d imensions in mm): A : 330 24,4 +2 30,4 60 13 +0,5 / -0,2
A C N
W1 : W2 (max) : N (m in) C : :
W1
The minimum bending radius is 45 mm. The mounting surface of the filters faces the bottom side of the embossed carrier tape. Markings on the filters can be read if the upper side of the carrier tape is regarded with the sprocket holes on its right.
TELEFILTER GmbH Potsdamer Strae 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: tft@telefilter.com VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.
TFS167G.doc
version 2.2
14.11.2003
VI TELEFILTER
Air reflow temperature conditions
Filter specification
TFS 167 G
4/5
1st and 2nd air reflow profile Name: Temperature: Time: pre-heating periods 150 C - 170 C 60 sec. - 90 sec. main-heating periods over 200 C 20 sec. - 25 sec. peak temperature 255 C 5 C
Chip-mount air reflow profile
260 240 220 200 180 temperature / C 160 140 120 100 80 60 40 20 0 0 20 40 60 80 100 120 time / sec. 140 160 180 200 220 240
Table for temperature vs. time during the air reflow process Tolerance of temperatures: 5 C time / sec. 0 10 20 30 40 50 60 70 80 90 100 110 120 130 temperature / C 23 34 46 60 80 103 121 134 143 150 154 156 158 159 time / sec. 140 150 160 170 180 190 195 200 205 210 215 220 230 240 temperature / C 160 161 164 170 180 205 230 255 230 205 180 165 140 120
TELEFILTER GmbH Potsdamer Strae 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: tft@telefilter.com VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.
TFS167G.doc
version 2.2
14.11.2003
VI TELEFILTER
History
Version 1.0 2.0 2.1 2.2 Reason of Changes
Filter specification
TFS 167 G
5/5
Name Dr. S. Sabah Dr. S. Sabah Roizengaft
Date 24.04.2003 23.07.2003 07.11.2003
generate development specification according to customer requirements generate Filter specification ; add of typ. values and terminating impedance change of relative attenuation change of relative attenuation, change of definition of insertion loss, add amplitude ripple in passband
Roizengaft
14.11.2003
TELEFILTER GmbH Potsdamer Strae 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: tft@telefilter.com VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.

▲Up To Search▲

Price & Availability of TFS167G

	To Download TFS167G Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .